UNO Windows & Doors | Blog

NZ building code: Latest updates to H1 Energy Efficiency

Written by UNO Windows & Doors | Jul 31, 2022, 8:05:00 PM

UNO Windows & Doors supports project teams with H1 compliance, including project-specific construction R-values from UNO Hub. This article explains which H1 documents apply now and what the reference R-values mean for windows and doors in each climate zone.

Last reviewed: November 2026

*Reflects H1/AS1 and H1/VM1 6th edition and H1/AS2 and H1/VM2 2nd edition, effective 27 November 2025.

Toward the tail end of 2021, it was announced by the Ministry of Business, Innovation and Employment that the New Zealand Building Code H1 energy efficiency rules would be changing in 2022. The changes announced would be the biggest advancements to the Building Code in over a decade.

These changes, specifically around insulation, will help boost the energy efficiency of homes. MBIE estimates the H1 insulation changes reduce the energy needed to heat new homes by around 40%, resulting in both dramatic energy bill reductions and positive health aspects for Kiwis. The positive environmental impact of these insulation changes will help support the country’s efforts in achieving net-zero carbon emissions by 2050 too.

The requirements vary according to which of the six climate zones the building is in. 

A broad overview of the insulation changes reveals that for all residential buildings (including apartments) and non-residential buildings less than 300m², roofing insulation requirements almost doubled and H1/AS1 and H1/VM1 window insulation levels increased significantly too. Wall insulation requirements remained relatively unchanged at that stage, due to the supply and design complexities these changes present.

In this article, we focus specifically on window insulation. We cover the changes you need to know about, including which H1 documents apply now and what impact they have on your projects.

 

Why is the building code changing?

The Building Code exists as a minimum standard for a range of 8 categories spanning classified uses (A1) to energy efficiency (H1) that all new buildings in New Zealand must comply with. When we compare our standards to other International Energy Agency (IEA) countries around the globe however, New Zealand is lagging behind. 

Changes to our Building Code are well overdue. These new insulation changes will help to lift the standard of construction, bringing it closer to other international standards. They’ll raise the health of Kiwi homes, boosting the wellbeing of the whānau they house and reduce power bills which overall will be kinder on wallets and gentler to the environment helping make sure our buildings are prepared for the future effects of climate change too.

Future proposed improvements to the New Zealand Building Code are also currently being considered, which include reviewing the interface, or junction, of the windows with the wall cladding, air leakage of the building envelope, and ventilation requirements for healthy homes.

Get DWGs and technical files in UNO Hub

 

Which H1 documents apply now?

The window insulation increases were phased in by climate zone between November 2022 and November 2023. The current documents were all published and took effect on 27 November 2025:

  • H1/AS1 and H1/VM1 6th edition, for housing and buildings up to 300 m²
  • H1/AS2 and H1/VM2 2nd edition, for buildings over 300 m²

The previous editions (H1/AS1 and H1/VM1 5th edition, H1/AS2 and H1/VM2 1st edition) can be used until 26 November 2026.

The Schedule Method has been removed in the current editions. Compliance is now shown using the Calculation Method or the Modelling Method.

 

How does it affect window insulation?

Under H1/AS1 and H1/VM1, the reference R-value for windows and doors depends on the climate zone you are building in.

An R-value is essentially a measure of thermal resistance, or the ability to prevent the transfer of heat. The larger the number, the harder that insulation is working at preventing heat conduction. The less heat loss, the lower your energy bills, the warmer your home, and the healthier your family. In warmer climates, the R-value prevents external heat from being transferred into the home, which reduces the need to cool the home in the summer too.

Before the changes, the window R-value minimum requirement was R0.26, which achieved compliance with the use of non-thermal aluminium windows & clear double glazing. Today there is no minimum window R-value. Instead, the design is compared with a reference building, with reference windows and doors of R0.46 in climate zones 1–4 and R0.50 in zones 5–6. The Calculation Method also requires glazing to be 40% or less of the gross wall area. Higher window R-values can be achieved with various solutions such as heat reflective glass with Low-E coatings, uPVC or timber frames, or aluminium thermally broken window frames such as UNO Thermal.

For comparison, the H1/AS1 generic values for double-glazed windows (Table D.1.1.1) are R0.24–R0.39 for standard aluminium and R0.30–R0.52 for thermally broken aluminium.

The country had previously been divided into three climate zones with the Central Plateau and the entire South Island making up zone 3, and Northland and the rest of the North Island spanning zones 1 and 2 respectively. The climate zones have since been reviewed and fine-tuned, dividing the country now into 6 climate zones. See the map below for these zones and continue reading for more information on what the reference R-values mean for each of these zones.

Source: https://www.mbie.govt.nz/dmsdocument/13808-consultation-document-building-code-update-2021

Zones 1 and 2: reference R0.46

In Zones 1 and 2, including Northland, Auckland, Coromandel, Bay of Plenty, Hamilton, East Coast and Taranaki, the reference windows and doors are R0.46. Because the design is compared with a reference building, windows below this value mean the rest of the building has to make up the difference.

A UNO Thermal fixed window (1000 × 1200 mm) has a typical construction R-value of R0.65*, while a UNO Non Thermal fixed window is R0.43* and a UNO Non Thermal sliding door is R0.42*.

Zones 3 and 4: reference R0.46 

In Zones 3 and 4, including Manawatu, Horowhenua, Wellington, Nelson, Marlborough, Chatham Islands, Central Plateau, Wairarapa and the West Coast, the reference windows and doors are also R0.46. Thermally broken aluminium frames such as UNO Thermal, with double-glazed Low-E glass and a thermal spacer, help you meet or exceed it. For example, a UNO Thermal sliding door (2100 × 2400 mm) has a typical construction R-value of R0.60*.  

Zones 5 and 6: reference R0.50

In Zones 5 and 6, including Canterbury, Coastal Otago, Inland Otago, Southland and Stewart Island, the reference windows and doors are R0.50.

Thermally broken aluminium frames, with argon-filled, double-glazed Low-E glass and a thermally improved spacer, help achieve higher R-values. A UNO Thermal entrance door with UNO door panel (1000 × 2100 mm) has a typical construction R-value of R0.62*, and a UNO Thermal glazed hinged door (1000 × 2100 mm) is R0.50*.

Across all climate zones, UNO recommends Low-E Lightbridge and Low-E Xcel. Low-E Xtreme or Performatech can be used to increase the R-value further if required.

Buildings over 300 m²

For buildings over 300 m² (H1/AS2 and H1/VM2), the reference windows and doors are R0.33 in zones 1–2, R0.37 in zones 3–4, R0.40 in zone 5 and R0.42 in zone 6. The H1/AS2 Calculation Method requires a solar aperture of 0.4 or less. Curtain walling, including UNO Commercial 100 mm and 150 mm, must be modelled under H1/VM1 or H1/VM2.

*Typical construction R-values from UNO Hub for the stated sizes and configurations, with Low-E Lightbridge double glazing (Ug 1.1, SHGC 0.56) or the UNO door panel. R-values vary with size, configuration, glass and panel. Sign up to UNO Hub to generate the construction R-values for your project.

 

Will the building code changes increase the cost of building?

In short, yes. Meeting a higher standard of insulation will naturally come at a higher cost. There remain some discrepancies on what the expected cost increase will be, but regardless of the new upfront cost, it may balance itself out over time. Money saved from energy efficiency gains and the benefits yielded from healthier families may help offset the increased up-front costs. 

Overall, the longevity of homes built to the new standards and the long-term positive impacts on our environment, as well as the health and wellbeing of our whānau and tamariki, are the intended benefits of these changes. 

The UNO Windows & Doors team can help you meet the current H1 requirements for your region, and UNO Hub lets you generate the construction R-values for your project. 

If you have questions about how the H1 changes could affect you, or your clients’ upcoming projects, or you require additional resources surrounding these changes, our team are here to help. Get in touch and we’ll supply you with the resources and advice you need.

 

Disclaimer
The information in this article is provided for general information purposes only and reflects the Building Code documents and standards current at the "Last reviewed" date shown on this article. It does not constitute technical, engineering or legal guidance for any specific project. Building Code documents and standards are subject to change; readers should refer to the current version of the relevant document and confirm all requirements with their designer, engineer and Building Consent Authority before proceeding. Construction R-values and product performance are project-specific and should be confirmed using the values generated in UNO Hub for the project concerned. UNO Windows & Doors accepts no liability for any loss or outcome arising from reliance on, or interpretation of, the information provided.